44++ Do I Need To Replace Fan Clutch With Water Pump Info
Do i need to replace fan clutch with water pump. Can anyone tell me a part number and source of a 17 solid blade fan and clutch for reverse flow. Step 1 Position the strap wrench to the water pumps pulley to keep the pulley from turning while you take off the bolt on the front of the water pump where the fan clutch is attached. Youll need a set of basic hand tools wrenches 38 drive sockets ratchet and extensions. A failing fan clutch could leave you stranded with expensive repair bills so pay attention to these symptoms. Fan speed does not increase when engine is hot. Poor AC performance at idle or low vehicle speeds. What should I do. Hold the Water Pump Pulley. You will need to make or buy a tool to hold the water pump pulley from turning while you unscrew the fan clutch from the water pump. I need to change the water pump but cant get the fan off due to the nut. Its on the original fan clutch and water pump with 11 years and 126000 miles. Both parts tend to wear out at about the same time so if one is giving you trouble the other may not.
Once youve run all bolts in finger tight use your wrench to tighten them according to factory specifications refer to your service manual or instructions with the new fan clutch. Off of the water pump. You want to replace this before it comes completely apart or it will destroy the radiator when it comes apart. They make a special tool for this which you can get from Amazon for about 2000 bucks or you can rent one for free from your local auto parts store. Do i need to replace fan clutch with water pump On a 1999 Chevy S-10 Blazer how do you get the fan clutch assy. However if you have a replacement that will require. Factoring all this in maybe its worth the wait to replace the water pump. Fan spins excessively when engine is stopped three or more times when hot engine is shut off. Also is it left or right. And unless your fan clutch is bad then there is no need to replace it. Regardless of manufacturer removing a fan clutch requires a specific tool called a strap wrench. If the car has 60000 miles on it this is the first time you are replacing the water pump and none of the seals are leaking you might be okay. If the water pump fails and the engine cannot be further damaged the labor costs are around 200.
5pc Fan Clutch Water Pump Service Holder Wrench Tool Set Autotool Buy Fan Clutch Wrench Fan Clutch Tool Autotool Product On Alibaba Com
Do i need to replace fan clutch with water pump According to Hayden here are some signs your fan clutch might need replaced.
Do i need to replace fan clutch with water pump. There is more to consider. It will include a serpentine accessory drive system with reverse flow water pump. But if your ac still doesnt work when moving then there is.
I am installing a GMPP Fast Burn 385 crate engine in my 72. One smart strategy is to have your vehicles fan clutch and water pump replaced together. A properly-functioning fan clutch is critical to engine reliability as it works to maintain a safe temperature range.
The engine cooling fan made of plastic or metal isnt hard-connected to the fan pulley or water pump but instead is soft-connected via the fan clutch. You must hold the water pump pulley in order to remove the fan clutch from the water pump. I know it is threaded but I cant figure out how to hold the pulley to get the fan off.
When changing a water pump replace all old gaskets and seals with new ones. Fan is always on at startup but when you rev it up to 2500 it always disengages. Slide the fan assembly back into the engine compartment paying special attention to the water pump shaft alignment.
Hi Redneck8814 Do you have the special tools. Some seals are so thin you could easily damage them when you rip off the packaging. The clutch fans on these trucks are not real good to begin with so slow speed and stopped they dont pull a ton of air through and can lead to poor ac performance.
To replace water pumpremove the radiator shroud halvesremove fan clutch and fanyou need fan clutch wrench and a fan clutch pulley holderyou can rent tools at auto zone or buy them at a auto parts storethe fan clutch bolts are left hand thread. Should I also replace the fan clutch while I have everything taken apart. Begin by separating the clutch from the fan.
I had a 17inch solid blade fan with thermal clutch and shroud with the old v-belt drive which worked great. On most domestic-brand pickups and SUVs the fan is held to the clutch by a circle of screws or bolts and the clutch is. Put the fan back into the engine.
If your new pump comes with a seal make sure its in impeccable condition before installing it. If it is not leaking coolant then the looseness must be the fan clutch. 1 You should start by removing the plastic fan shroud from the radiatorIf its a 2-piece shroud you can remove the top half completely which makes it a LOT easier to access the front of the engineIf its a single piece then youll have to do steps 1 and 2 at the same time.
To my surprise a LOT of people are commenting that if the water pump is replaced the clutch should be too not sure about that.
Do i need to replace fan clutch with water pump To my surprise a LOT of people are commenting that if the water pump is replaced the clutch should be too not sure about that.
Do i need to replace fan clutch with water pump. 1 You should start by removing the plastic fan shroud from the radiatorIf its a 2-piece shroud you can remove the top half completely which makes it a LOT easier to access the front of the engineIf its a single piece then youll have to do steps 1 and 2 at the same time. If it is not leaking coolant then the looseness must be the fan clutch. If your new pump comes with a seal make sure its in impeccable condition before installing it. Put the fan back into the engine. On most domestic-brand pickups and SUVs the fan is held to the clutch by a circle of screws or bolts and the clutch is. I had a 17inch solid blade fan with thermal clutch and shroud with the old v-belt drive which worked great. Begin by separating the clutch from the fan. Should I also replace the fan clutch while I have everything taken apart. To replace water pumpremove the radiator shroud halvesremove fan clutch and fanyou need fan clutch wrench and a fan clutch pulley holderyou can rent tools at auto zone or buy them at a auto parts storethe fan clutch bolts are left hand thread. The clutch fans on these trucks are not real good to begin with so slow speed and stopped they dont pull a ton of air through and can lead to poor ac performance. Some seals are so thin you could easily damage them when you rip off the packaging.
Hi Redneck8814 Do you have the special tools. Slide the fan assembly back into the engine compartment paying special attention to the water pump shaft alignment. Do i need to replace fan clutch with water pump Fan is always on at startup but when you rev it up to 2500 it always disengages. When changing a water pump replace all old gaskets and seals with new ones. I know it is threaded but I cant figure out how to hold the pulley to get the fan off. You must hold the water pump pulley in order to remove the fan clutch from the water pump. The engine cooling fan made of plastic or metal isnt hard-connected to the fan pulley or water pump but instead is soft-connected via the fan clutch. A properly-functioning fan clutch is critical to engine reliability as it works to maintain a safe temperature range. One smart strategy is to have your vehicles fan clutch and water pump replaced together. I am installing a GMPP Fast Burn 385 crate engine in my 72. But if your ac still doesnt work when moving then there is.
Loose Water Pump Bolts Replacing Fan Clutch Yotatech Forums
It will include a serpentine accessory drive system with reverse flow water pump. There is more to consider. Do i need to replace fan clutch with water pump.
Do i need to replace fan clutch with water pump